1. 08 Apr, 2020 15 commits
  2. 07 Apr, 2020 4 commits
    • Rosen Penev's avatar
      iproute2: add kmod-netlink-diag for ss · d8bde368
      Rosen Penev authored
      Allows proper usage of the ss tool. Otherwise, several errors and bad
      data gets thrown:
      
      Cannot open netlink socket: Protocol not supported
      Cannot open netlink socket: Protocol not supported
      Cannot open netlink socket: Protocol not supported
      Cannot open netlink socket: Protocol not supported
      Cannot open netlink socket: Protocol not supported
      Cannot open netlink socket: Protocol not supported
      Cannot open netlink socket: Protocol not supported
      
      Originally reported here: https://github.com/openwrt/packages/issues/8232
      
      Signed-off-by: default avatarRosen Penev <rosenp@gmail.com>
      d8bde368
    • Rosen Penev's avatar
      kmod: add netlink-diag package · 92792ead
      Rosen Penev authored
      
      
      This is used by the ss utility from iproute2.
      Signed-off-by: default avatarRosen Penev <rosenp@gmail.com>
      92792ead
    • INAGAKI Hiroshi's avatar
      ramips: add support for Buffalo WSR-2533DHPL · e8787291
      INAGAKI Hiroshi authored
      
      
      Buffalo WSR-2533DHPL is a 2.4/5 GHz band 11ac router, based on MediaTek
      MT7621A.
      
      Specification:
      
      - SoC		: MediaTek MT7621A
      - RAM		: DDR3 128 MiB
      - Flash		: SPI-NOR 16 MiB
      - WLAN		: 2.4/5 GHz 4T4R (2x MediaTek MT7615N)
      - Ethernet	: 10/100/1000 Mbps
        - Switch	: MediaTek MT7530 (SoC)
      - LED/keys	: 8x/6x (3x buttons, 2x slide-switches)
      - UART		: through-hole on PCB
        - J4: 3.3V, GND, TX, RX from triangle-mark
        - 57600n8
      - Power		: 12VDC 1.5A
      
      Flash instruction using initramfs image:
      
      1. prepare the TFTP server with the initramfs image renamed to
         "linux.trx-recovery" and IP address "192.168.11.2"
      2. press the "AOSS" button while powering on the WSR-2533DHPL
      3. after 10 seconds, release the "AOSS" button, WSR-2533DHPL downloads
         the initramfs image and boot with it automatically
      4. on the initramfs image, download the sysupgrade image to the device
         and perform sysupgrade with it
      5. wait ~120 seconds to complete flashing
      
      Switch position overview:
      
      - slide-switch1 (2x positions)
        - "AUTO"
        - "MANUAL" (not connected to gpio)
      
      - slide-switch2 (3x positions)
        - "ROUTER"
        - "AP" (not connected to gpio)
        - "WB"
      Signed-off-by: default avatarINAGAKI Hiroshi <musashino.open@gmail.com>
      [add note on switches, fix group->groups for state_default]
      Signed-off-by: default avatarAdrian Schmutzler <freifunk@adrianschmutzler.de>
      e8787291
    • Dan Haab's avatar
      bcm53xx: add support for Luxul FullMAC WiFi devices · c459a6bf
      Dan Haab authored
      
      
      This prepares support for models XAP-1610 and XWR-3150. Flashing
      requires using Luxul firmware version:
      1) 8.1.0 or newer for XAP-1610
      2) 6.4.0 or newer for XWR-3150
      and uploading firmware using "Firmware Update" web UI page.
      Signed-off-by: default avatarDan Haab <dan.haab@legrand.com>
      c459a6bf
  3. 06 Apr, 2020 17 commits
  4. 05 Apr, 2020 4 commits