GitLab

This can be used to tweak the buildbot behavior without having to change
buildbot's configuration.
It will also allow us to add more aggressive clean steps (e.g. on
toolchain changes), which would break developers' workflows if enable
by default.
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Include packages from the default profile for NAND devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add support for the EBR-2310, which is almost identical to the DIR-615
rev E4, without the wifi.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>

fixes issue "nsa 310b u-boot can initialize usb but cannot
use usb storage so it cannot load files from usb"
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>

TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.

Short specification:

- 550/391/195 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x internal antennas (embedded on PCB)
- 9x LED (all can be turned off with GPIO15), 2x button
- UART (J3) header on PCB

Flash instruction: use "factory" image directly in vendor GUI.

Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.

You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin

Image was tested only in US version of the device, but should work
also with the same device version sold in other countries.

Available FLASH space, with LEDE trunk, is only 240 KB.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

At the tail of dtsi, wmac is enabled twice, clean the first one
Signed-off-by: Furong Xu <xfr@outlook.com>

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>

The WN3000RPv3 is a repeater with a single ethernet port. Setting up the
switch, even to disable it, is unnecessary and possibly confusing.

Configure LAN as eth0 instead.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>

Bump qca9984 firmware.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

The list of v2/v3 devices is getting longer and makes reading the names of
the profiles unnecessary hard.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

NAND support is missing
Signed-off-by: John Crispin <john@phrozen.org>

as we do for IPv4 PPP interfaces. When we create the
dynamic IPv6 interface we should inherit ip6table from
main interface.
Signed-off-by: Ulrich Weber <ulrich.weber@riverbed.com>

pppoe-discovery performs the same discovery process as pppoe, but does
not initiate a session
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>

Fixes the following issue:

root@LEDE:/# sysupgrade /tmp/lede-mvebu-armada-388-clearfog-sdcard.img.gz
Saving metaconfig...
Image metadata not found
Use sysupgrade -F to override this check when downgrading or flashing to vendor firmware
Image check 'fwtool_check_image' failed.
root@LEDE:/#
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>

Avoids shipping potentially incompatible object files and also reduces
the tarball size
Signed-off-by: Felix Fietkau <nbd@nbd.name>

It has been reported to cause random reboots on some devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Signed-off-by: John Crispin <john@phrozen.org>