Commit b56bcfe3 authored by Sven Roederer's avatar Sven Roederer Committed by Adrian Schmutzler
Browse files

ath79: add support for Ubiquiti Nanostation Loco M (XM)



This adds support for the Ubiquiti Nanostation Loco M (XM), which
has the same board/LEDs as the Bullet M XM, but different case and
antennas.

Specifications:
- AR7241 SoC @ 400 MHz
- 32 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
- NS Loco M2: built-in antenna: 8 dBi; AR9287
- NS Loco M5: built-in antenna: 13 dBi; 2T2R 5 GHz radio
- POWER/LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1) on PCB

Flashing via WebUI:
  Upload the factory image via the stock firmware web UI.
  Note that only certain firmware versions accept unsigned
  images. Refer to the device's Wiki page for further information.

Flashing via TFTP:
  Same procedure as other NanoStation M boards.

- Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
  button on the device or on the PoE supply pressed
- Power on the device via PoE (keep reset button pressed)
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
  LED2+LED4 => LED1+LED3, etc.
- Release reset button
- The device starts a TFTP server at 192.168.1.20
- Set a static IP on the computer (e.g., 192.168.1.21/24)
- Upload via tftp the factory image:
  $ tftp 192.168.1.20
  tftp> bin
  tftp> trace
  tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-squashfs-factory.bin

Tested on NanoStation Loco M2.
Signed-off-by: default avatarSven Roederer <freifunk@it-solutions.geroedel.de>
Co-developed-by: default avatarAdrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: default avatarAdrian Schmutzler <freifunk@adrianschmutzler.de>
parent 98fbf2ed
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include "ar7241_ubnt_xm_outdoor.dtsi"
/ {
compatible = "ubnt,nanostation-loco-m", "ubnt,xm", "qca,ar7241";
model = "Ubiquiti Nanostation Loco M";
};
&eth1 {
compatible = "syscon", "simple-mfd";
};
......@@ -244,6 +244,7 @@ trendnet,tew-823dru)
;;
ubnt,bullet-m|\
ubnt,bullet-m-xw|\
ubnt,nanostation-loco-m|\
ubnt,nanostation-loco-m-xw|\
ubnt,nanostation-m|\
ubnt,nanostation-m-xw|\
......
......@@ -47,6 +47,7 @@ ath79_setup_interfaces()
ubnt,litebeam-ac-gen2|\
ubnt,nanobeam-ac|\
ubnt,nanostation-ac-loco|\
ubnt,nanostation-loco-m|\
ubnt,nanostation-loco-m-xw|\
ubnt,rocket-m|\
ubnt,unifiac-lite|\
......@@ -426,6 +427,7 @@ ath79_setup_macs()
;;
ubnt,airrouter|\
ubnt,bullet-m|\
ubnt,nanostation-loco-m|\
ubnt,nanostation-m|\
ubnt,rocket-m|\
ubnt,unifi)
......
......@@ -90,6 +90,7 @@ case "$FIRMWARE" in
tplink,tl-wr842n-v1|\
ubnt,airrouter|\
ubnt,bullet-m|\
ubnt,nanostation-loco-m|\
ubnt,nanostation-m|\
ubnt,rocket-m)
caldata_extract "art" 0x1000 0x1000
......
......@@ -179,6 +179,14 @@ define Device/ubnt_nanostation-ac-loco
endef
TARGET_DEVICES += ubnt_nanostation-ac-loco
define Device/ubnt_nanostation-loco-m
$(Device/ubnt-xm)
DEVICE_MODEL := Nanostation Loco M
DEVICE_PACKAGES += rssileds
SUPPORTED_DEVICES += bullet-m
endef
TARGET_DEVICES += ubnt_nanostation-loco-m
define Device/ubnt_nanostation-loco-m-xw
$(Device/ubnt-xw)
DEVICE_MODEL := Nanostation Loco M
......
Supports Markdown
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment