Commit 9169482f authored by Sungbo Eo's avatar Sungbo Eo Committed by Chuanhong Guo
Browse files

ramips: add support for ipTIME A1004ns



ipTIME A1004ns is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A.

Specifications:
- SoC: MT7620A
- RAM: DDR2 128MB
- Flash: SPI NOR 16MB
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7610EN
- Ethernet: 5x 10/100/1000Mbps
  - Switch: MT7530BU
- USB: 1x 2.0
- UART:
  - J2: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.
Signed-off-by: default avatarSungbo Eo <mans0n@gorani.run>
parent d682dcc9
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include "mt7620a_iptime.dtsi"
/ {
compatible = "iptime,a1004ns", "ralink,mt7620a-soc";
model = "ipTIME A1004ns";
aliases {
led-boot = &led_cpu;
led-failsafe = &led_cpu;
led-running = &led_cpu;
led-upgrade = &led_cpu;
};
leds {
compatible = "gpio-leds";
led_cpu: cpu {
label = "a1004ns:blue:cpu";
gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
};
usb {
label = "a1004ns:blue:usb";
gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
trigger-sources = <&ohci_port1>, <&ehci_port1>;
linux,default-trigger = "usbport";
};
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
};
};
&firmware {
reg = <0x30000 0xfd0000>;
};
&state_default {
gpio {
ralink,group = "i2c", "uartf", "spi refclk";
ralink,function = "gpio";
};
};
&ethernet {
pinctrl-names = "default";
pinctrl-0 = <&rgmii1_pins &mdio_pins>;
port@5 {
status = "okay";
mediatek,fixed-link = <1000 1 1 1>;
phy-mode = "rgmii";
};
mdio-bus {
status = "okay";
ethernet-phy@0 {
reg = <0>;
phy-mode = "rgmii";
};
ethernet-phy@1 {
reg = <1>;
phy-mode = "rgmii";
};
ethernet-phy@2 {
reg = <2>;
phy-mode = "rgmii";
};
ethernet-phy@3 {
reg = <3>;
phy-mode = "rgmii";
};
ethernet-phy@4 {
reg = <4>;
phy-mode = "rgmii";
};
ethernet-phy@1f {
reg = <0x1f>;
phy-mode = "rgmii";
};
};
};
......@@ -503,6 +503,17 @@ define Device/iodata_wn-ac733gr3
endef
TARGET_DEVICES += iodata_wn-ac733gr3
define Device/iptime_a1004ns
SOC := mt7620a
IMAGE_SIZE := 16192k
UIMAGE_NAME := a1004ns
DEVICE_VENDOR := ipTIME
DEVICE_MODEL := A1004ns
DEVICE_PACKAGES := kmod-mt76x0e kmod-usb2 kmod-usb-ohci \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += iptime_a1004ns
define Device/iptime_a104ns
SOC := mt7620a
IMAGE_SIZE := 8000k
......
......@@ -143,7 +143,8 @@ ramips_setup_interfaces()
"0:lan" "1:lan" "5:wan" "6@eth0"
;;
iodata,wn-ac1167gr|\
iodata,wn-ac733gr3)
iodata,wn-ac733gr3|\
iptime,a1004ns)
ucidef_add_switch "switch0"
ucidef_add_switch_attr "switch0" "enable" "false"
ucidef_add_switch "switch1" \
......@@ -312,6 +313,9 @@ ramips_setup_macs()
iodata,wn-ac733gr3)
wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr)
;;
iptime,a1004ns)
wan_mac=$(mtd_get_mac_binary u-boot 0x1fc40)
;;
iptime,a104ns)
wan_mac=$(macaddr_add "$(mtd_get_mac_binary u-boot 0x1fc20)" 2)
;;
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment