Commit 4e931720 authored by Pawel Dembicki's avatar Pawel Dembicki Committed by David Bauer
Browse files

ramips: mt7621: add support for Netgear R6800



This patch adds support for the Netgear R6800, aka Netgear AC1900 and
R6800-100PES.

Specification:
- SoC: MediaTek MT7621AT (880 MHz)
- Flash: 128 MiB NAND
- RAM: 256 MiB
- Wireless: MediaTek MT7615EN b/g/n , MediaTek MT7615EN an+ac
- LAN speed: 10/100/1000
- LAN ports: 4
- WAN speed: 10/100/1000
- WAN ports: 1
- USB 2.0
- USB 3.0
- Serial baud rate of Bootloader and factory firmware: 57600

Known issues:
- Device has 3 wifi LEDs: Wifi 5Ghz, Wifi 2.4Ghz and Wifi on/off.
  Wifi on/off is not used.

Installation:
- apply factory image via stock web-gui.

Back to stock:
- nmrpflash can be used to recover to the stock Netgear firmware.
Signed-off-by: default avatarPawel Dembicki <paweldembicki@gmail.com>
parent 3251ac8f
// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include "mt7621_netgear_sercomm_bzv.dtsi"
/ {
compatible = "netgear,r6800", "mediatek,mt7621-soc";
model = "Netgear R6800";
aliases {
led-boot = &led_power_white;
led-failsafe = &led_power_orange;
led-running = &led_power_white;
led-upgrade = &led_power_orange;
label-mac-device = &ethernet;
};
leds {
compatible = "gpio-leds";
led_power_orange: power_orange {
gpios = <&gpio_expander 0 GPIO_ACTIVE_LOW>;
label = "r6800:orange:power";
};
led_power_white: power_white {
gpios = <&gpio_expander 1 GPIO_ACTIVE_LOW>;
label = "r6800:white:power";
};
wan_orange {
gpios = <&gpio_expander 2 GPIO_ACTIVE_LOW>;
label = "r6800:orange:wan";
};
wan_white {
gpios = <&gpio_expander 3 GPIO_ACTIVE_LOW>;
label = "r6800:white:wan";
};
wlan2g {
gpios = <&gpio_expander 4 GPIO_ACTIVE_LOW>;
label = "r6800:white:wlan2g";
linux,default-trigger = "phy0radio";
};
wlan5g {
gpios = <&gpio_expander 5 GPIO_ACTIVE_LOW>;
label = "r6800:white:wlan5g";
linux,default-trigger = "phy1radio";
};
usb2 {
gpios = <&gpio_expander 6 GPIO_ACTIVE_LOW>;
label = "r6800:white:usb2";
linux,default-trigger = "usbport";
trigger-sources = <&ehci_port2>;
};
usb3 {
gpios = <&gpio_expander 7 GPIO_ACTIVE_LOW>;
label = "r6800:white:usb3";
linux,default-trigger = "usbport";
trigger-sources = <&xhci_ehci_port1>;
};
lan1_orange {
gpios = <&gpio_expander 8 GPIO_ACTIVE_LOW>;
label = "r6800:orange:lan1";
};
lan1_white {
gpios = <&gpio_expander 9 GPIO_ACTIVE_LOW>;
label = "r6800:white:lan1";
};
lan2_orange {
gpios = <&gpio_expander 10 GPIO_ACTIVE_LOW>;
label = "r6800:orange:lan2";
};
lan2_white {
gpios = <&gpio_expander 11 GPIO_ACTIVE_LOW>;
label = "r6800:white:lan2";
};
lan3_orange {
gpios = <&gpio_expander 12 GPIO_ACTIVE_LOW>;
label = "r6800:orange:lan3";
};
lan3_white {
gpios = <&gpio_expander 13 GPIO_ACTIVE_LOW>;
label = "r6800:white:lan3";
};
lan4_orange {
gpios = <&gpio_expander 14 GPIO_ACTIVE_LOW>;
label = "r6800:orange:lan4";
};
lan4_white {
gpios = <&gpio_expander 15 GPIO_ACTIVE_LOW>;
label = "r6800:white:lan4";
};
wps {
gpios = <&gpio0 17 GPIO_ACTIVE_HIGH>;
label = "r6800:white:wps";
};
wlan {
gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
label = "r6800:white:wlan";
};
};
};
&state_default {
gpio {
ralink,group = "uart3", "uart2", "jtag", "wdt";
ralink,function = "gpio";
};
};
// SPDX-License-Identifier: GPL-2.0
#include "mt7621.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
compatible = "mediatek,mt7621-soc";
chosen {
bootargs = "console=ttyS0,57600";
};
keys {
compatible = "gpio-keys";
wps {
label = "wps";
gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
rfkill {
label = "rfkill";
gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RFKILL>;
};
reset {
label = "reset";
gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
};
&pcie {
status = "okay";
};
&pcie0 {
wifi@0,0 {
compatible = "mediatek,mt76";
reg = <0x0 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x0>;
ieee80211-freq-limit = <2400000 2500000>;
};
};
&pcie1 {
wifi@0,0 {
compatible = "mediatek,mt76";
reg = <0x0 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x8000>;
ieee80211-freq-limit = <5000000 6000000>;
};
};
&ethernet {
mtd-mac-address = <&factory 0x4>;
};
&i2c {
status = "okay";
gpio_expander: i2c0gpio-expander@20{
#gpio-cells = <2>;
#interrupt-cells = <2>;
compatible = "semtech,sx1503q";
reg = <0x20>;
gpio-controller;
};
};
&nand {
status = "okay";
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x0 0x100000>;
read-only;
};
partition@100000 {
label = "SC PART_MAP";
reg = <0x100000 0x100000>;
read-only;
};
partition@200000 {
label = "kernel";
reg = <0x200000 0x400000>;
};
partition@600000 {
label = "ubi";
reg = <0x600000 0x2800000>;
};
partition@2e00000 {
label = "reserved0";
reg = <0x2e00000 0x1800000>;
read-only;
};
factory: partition@4600000 {
label = "factory";
reg = <0x4600000 0x200000>;
read-only;
};
partition@4800000 {
label = "reserved1";
reg = <0x4800000 0x3800000>;
read-only;
};
};
};
...@@ -595,6 +595,18 @@ define Device/netgear_r6350 ...@@ -595,6 +595,18 @@ define Device/netgear_r6350
endef endef
TARGET_DEVICES += netgear_r6350 TARGET_DEVICES += netgear_r6350
define Device/netgear_r6800
$(Device/netgear_sercomm_nand)
DEVICE_MODEL := R6800
SERCOMM_HWNAME := R6950
SERCOMM_HWID := BZV
SERCOMM_HWVER := A001
SERCOMM_SWVER := 0x0062
IMAGE_SIZE := 40960k
DEVICE_PACKAGES += kmod-mt7615e
endef
TARGET_DEVICES += netgear_r6800
define Device/netgear_r6850 define Device/netgear_r6850
$(Device/netgear_sercomm_nand) $(Device/netgear_sercomm_nand)
DEVICE_MODEL := R6850 DEVICE_MODEL := R6850
......
...@@ -52,6 +52,13 @@ netgear,r6850|\ ...@@ -52,6 +52,13 @@ netgear,r6850|\
netgear,wndr3700-v5) netgear,wndr3700-v5)
ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x10" ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x10"
;; ;;
netgear,r6800)
ucidef_set_led_switch "wan" "WAN" "$boardname:white:wan" "switch0" "0x10"
ucidef_set_led_switch "lan1" "LAN1" "$boardname:white:lan1" "switch0" "0x08"
ucidef_set_led_switch "lan2" "LAN2" "$boardname:white:lan2" "switch0" "0x04"
ucidef_set_led_switch "lan3" "LAN3" "$boardname:white:lan3" "switch0" "0x02"
ucidef_set_led_switch "lan4" "LAN4" "$boardname:white:lan4" "switch0" "0x01"
;;
tplink,re350-v1|\ tplink,re350-v1|\
tplink,re650-v1) tplink,re650-v1)
ucidef_set_led_netdev "wifi2g" "Wifi 2.4G" "$boardname:blue:wifi2G" "wlan0" ucidef_set_led_netdev "wifi2g" "Wifi 2.4G" "$boardname:blue:wifi2G" "wlan0"
......
...@@ -41,6 +41,7 @@ ramips_setup_interfaces() ...@@ -41,6 +41,7 @@ ramips_setup_interfaces()
netgear,r6220|\ netgear,r6220|\
netgear,r6260|\ netgear,r6260|\
netgear,r6350|\ netgear,r6350|\
netgear,r6800|\
netgear,r6850|\ netgear,r6850|\
netgear,wndr3700-v5|\ netgear,wndr3700-v5|\
netis,wf2881|\ netis,wf2881|\
...@@ -252,6 +253,7 @@ ramips_setup_macs() ...@@ -252,6 +253,7 @@ ramips_setup_macs()
;; ;;
netgear,r6260|\ netgear,r6260|\
netgear,r6350|\ netgear,r6350|\
netgear,r6800|\
netgear,r6850) netgear,r6850)
wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 0x4)" 2) wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 0x4)" 2)
;; ;;
......
...@@ -48,6 +48,7 @@ platform_do_upgrade() { ...@@ -48,6 +48,7 @@ platform_do_upgrade() {
netgear,r6220|\ netgear,r6220|\
netgear,r6260|\ netgear,r6260|\
netgear,r6350|\ netgear,r6350|\
netgear,r6800|\
netgear,r6850|\ netgear,r6850|\
netis,wf2881|\ netis,wf2881|\
xiaomi,mir3g|\ xiaomi,mir3g|\
......
...@@ -236,6 +236,7 @@ CONFIG_PHYLIB=y ...@@ -236,6 +236,7 @@ CONFIG_PHYLIB=y
CONFIG_PINCTRL=y CONFIG_PINCTRL=y
CONFIG_PINCTRL_RT2880=y CONFIG_PINCTRL_RT2880=y
# CONFIG_PINCTRL_SINGLE is not set # CONFIG_PINCTRL_SINGLE is not set
CONFIG_PINCTRL_SX150X=y
CONFIG_POWER_RESET=y CONFIG_POWER_RESET=y
CONFIG_POWER_RESET_GPIO=y CONFIG_POWER_RESET_GPIO=y
CONFIG_POWER_SUPPLY=y CONFIG_POWER_SUPPLY=y
......
Supports Markdown
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment